在环氧地坪施工完工后,因为面漆需要有一定的固化时间,要确保周边环境避免日晒风吹灰尘的侵入,并且需要保养至一周以后在投入使用,这样环氧地坪漆的强度和硬度已经到达最好的时候了。虽然环氧地坪漆施工工艺看起来是比较简单的,但是要做出优质的环氧地坪漆工程,在实际施工过程中还是有许多需要注意的地方,下面环氧地坪漆厂家就给大家分享环氧地坪漆施工过程中的几个小技巧。
After the construction of epoxy flooring, the strength and hardness of epoxy flooring paint have reached the best time, because it needs a certain curing time to ensure that the surrounding environment avoids the invasion of sunshine, wind and dust, and needs to be maintained until a week later. Although the construction technology of epoxy floor paint seems relatively simple, there are still many points needing attention in the actual construction process to make a high quality epoxy floor paint project. Here are some tips for epoxy floor paint manufacturers to share with you in the construction process.
环氧底漆施工技巧:
Construction techniques of epoxy primer:
环氧底漆层施工是连接环氧地坪涂层与基层地面最为关键的一步,环氧底漆具有很好的渗透性,能够渗透到基层地面内部去,起到封闭地面和保护地面的作用,同时提高环氧地坪涂层的附着力。
The construction of epoxy primer layer is the most critical step to connect epoxy floor coating with base floor. Epoxy primer has good permeability, can penetrate into the base floor interior, play the role of closing the ground and protecting the ground, and improve the adhesion of epoxy floor coating.
环氧底漆施工完工后一定要检查是否施工到位,最简单方法就是看:一看刷涂的是否均匀,二看是否有漏涂,三看是否有堆积的现象。待底漆完全干透之后才能进行环氧中涂层的施工。
After finishing the construction of epoxy primer, we must check whether the construction is in place. The simplest way is to see: first, whether the brush is uniform, second, whether there is leakage, and third, whether there is accumulation. The epoxy coating can not be applied until the primer is completely dried out.
环氧中涂施工技巧:
Construction techniques of epoxy intermediate coating:
环氧底漆施工后,一般基层地面上的空隙,裂纹凹凸不平的缺陷都可以看的很清楚,比如这些裂纹如果是比较大的需要切V字槽然后灌环氧砂浆,麻面或者坑洞都用较稠的环氧砂浆填平,然后在整体刮环氧砂浆,待砂浆层干透后再打磨刮涂两遍环氧腻子层,用于填平环氧砂浆层产生骨料之间的细小间隙。
After the construction of epoxy primer, the voids and cracks on the general base floor can be clearly seen. For example, if these cracks are larger, they need to cut V-slots and then pour epoxy mortar. The flax surface or pits are filled with thicker epoxy mortar, and then scraped epoxy mortar as a whole, after the mortar layer dries through. The epoxy putty layer is polished and scraped twice to fill the fine gap between the aggregates in the epoxy mortar layer.
环氧面漆施工技巧:
Construction Skills of Epoxy Topcoat:
环氧面漆施工一般采用滚涂或者镘涂的方法。滚涂面漆要求一次涂得薄而均匀,即使遮盖力差的面漆,也不能简单地依靠增加一次的施工厚度来弥补,而应分几次涂装。对于无溶剂环氧自流平环氧地坪漆要求一次镘涂成型,施工时要特别精心操作,由于这类涂料黏度较大,配料的时候一定要搅拌均匀,防止桶底和桶壁黏附的涂料得不到有效的混合,造成局部不干和固化不良的现象。 本站网址:http://www.wuxispeed.com
|